Conversion from Megaoctets per second to Gibibits per second

=

Invert

Formula to convert Megaoctets per second (Mo/s) to Gibibits per second (Gibit/s)

More information

Megaoctets per second to Gibibits per second conversion table

Megaoctets per second (Mo/s)Gibibits per second (Gibit/s)
1 Megaoctet per second0.00745058059692 Gibit/s
2 Megaoctets per second0.0149011611938 Gibit/s
3 Megaoctets per second0.0223517417908 Gibit/s
4 Megaoctets per second0.0298023223877 Gibit/s
5 Megaoctets per second0.0372529029846 Gibit/s
10 Megaoctets per second0.0745058059692 Gibit/s
20 Megaoctets per second0.149011611938 Gibit/s
25 Megaoctets per second0.186264514923 Gibit/s
50 Megaoctets per second0.372529029846 Gibit/s
100 Megaoctets per second0.745058059692 Gibit/s

Data-transfer rate reference points

ReferenceMegaoctets per second (Mo/s)Gibibits per second (Gibit/s)
A dial-up modem0.007 Mo/s0.0000521541 Gibit/s
Typical home broadband12.5 Mo/s0.0931323 Gibit/s
Gigabit Ethernet125 Mo/s0.931323 Gibit/s
Streaming a 4K film3.125 Mo/s0.0232831 Gibit/s

Try our other unit converters

LengthMassTemperatureEnergyVolumeSpeedTimeDataPressureFrequencyData-transfer rateVolumetric flow rateAngleArea

Information about the Megaoctet per second (Mo/s)

The megaoctet per second is a unit of data transfer rate equal to one million octets per second, or eight megabits per second. Its symbol is Mo/s. It is the unit in which storage devices and their interfaces are rated, and the one a file manager shows while a copy is running.

Storage speeds fall naturally into this range. A mechanical hard drive sustains 100 to 250 megaoctets per second on sequential reads. A solid-state drive on the older interface reaches about 550, which is the limit of that interface rather than of the drive. A modern drive on the faster interface reaches several thousand, at which point the unit gives way to gigaoctets per second.

Interface speeds tell the same story from the other side. The successive versions of the universal serial bus have offered roughly 1.5, 60, 625 and 2,500 megaoctets per second at their nominal rates, and memory card standards have followed a similar path. A device is always limited by whichever of the two is slower, and matching them is the practical art of building a fast system.

For everyday sizes, one megaoctet per second transfers a photograph in a couple of seconds and a two-gigaoctet film in about half an hour. At 500 megaoctets per second the same film takes four seconds. That contrast explains why the perceived speed of a computer changed so completely when solid-state storage replaced mechanical drives, even though processors improved far less over the same period.

Sequential rates like these are the best case. Reading many small files instead of one large one costs far more, because each file requires locating its data and reading its record. A drive that sustains 500 megaoctets per second in sequence may manage only a few tens when copying a directory of thousands of small files, and that is where the difference between drive technologies is most visible.

The unit also describes the throughput of a busy network connection: a gigabit link delivers 125 megaoctets per second at best, so a fast local network and a fast drive are now comparable, and neither is obviously the limiting factor in a transfer.

One megaoctet per second equals 1,000,000 octets per second, 8 megabits per second, or about 0.9537 mebioctets per second.


Information about the Gibibit per second (Gibit/s)

The gibibit per second is a unit of data transfer rate equal to 1,073,741,824 bits per second. Its symbol is Gibit/s. It is the binary counterpart of the gigabit per second, and the two now differ by 7.4 per cent, which is enough to matter in any engineering specification.

The unit belongs to the inside of a machine rather than to the network. Memory buses, processor interconnects and the links between chips on the same board all move a power-of-two number of bits per clock cycle, so their throughput is naturally expressed with a binary prefix. A bus sixty-four bits wide clocked at a given frequency delivers a rate that is a binary multiple of that frequency.

Networking, by contrast, is decimal all the way down. Gigabit Ethernet carries exactly one thousand million bits per second, not 1,073,741,824, and the symbol rate on the wire is chosen to make that so. Confusing the two overstates a link's capacity by seven per cent, which in a capacity plan is the difference between adequate and insufficient.

In octets a gibibit per second is 134,217,728, or 128 mebioctets per second. That is close to the throughput of a fast mechanical hard drive and well below a modern solid-state drive, so it sits at the point where storage and internal buses meet and where matching their rates becomes a design question.

Benchmark tools are the commonest place to see the unit written correctly. A memory bandwidth test that allocates buffers in powers of two and measures how long they take to traverse naturally reports in gibibits or gibioctets per second, and a well-written tool says so explicitly rather than rounding to the decimal unit.

The reason to insist on the distinction here rather than lower down the scale is arithmetic. At the kibibit the gap was 2.4 per cent and could be ignored; here it is nearly a thirteenth, and it grows by a further 2.4 per cent at every step above. Getting into the habit at this level costs nothing and avoids compounding errors later.

One gibibit per second equals 1,073,741,824 bits per second, 134,217,728 octets per second, or about 1.074 gigabits per second.