Conversion from Megaoctets per second to Gigabits per second

Information about the Megaoctet per second (Mo/s)

The megaoctet per second is a unit of data transfer rate equal to one million octets per second, or eight megabits per second. Its symbol is Mo/s. It is the unit in which storage devices and their interfaces are rated, and the one a file manager shows while a copy is running.

Storage speeds fall naturally into this range. A mechanical hard drive sustains 100 to 250 megaoctets per second on sequential reads. A solid-state drive on the older interface reaches about 550, which is the limit of that interface rather than of the drive. A modern drive on the faster interface reaches several thousand, at which point the unit gives way to gigaoctets per second.

Interface speeds tell the same story from the other side. The successive versions of the universal serial bus have offered roughly 1.5, 60, 625 and 2,500 megaoctets per second at their nominal rates, and memory card standards have followed a similar path. A device is always limited by whichever of the two is slower, and matching them is the practical art of building a fast system.

For everyday sizes, one megaoctet per second transfers a photograph in a couple of seconds and a two-gigaoctet film in about half an hour. At 500 megaoctets per second the same film takes four seconds. That contrast explains why the perceived speed of a computer changed so completely when solid-state storage replaced mechanical drives, even though processors improved far less over the same period.

Sequential rates like these are the best case. Reading many small files instead of one large one costs far more, because each file requires locating its data and reading its record. A drive that sustains 500 megaoctets per second in sequence may manage only a few tens when copying a directory of thousands of small files, and that is where the difference between drive technologies is most visible.

The unit also describes the throughput of a busy network connection: a gigabit link delivers 125 megaoctets per second at best, so a fast local network and a fast drive are now comparable, and neither is obviously the limiting factor in a transfer.

One megaoctet per second equals 1,000,000 octets per second, 8 megabits per second, or about 0.9537 mebioctets per second.

Information about the Gigabit per second (Gbit/s)

The gigabit per second is a unit of data transfer rate equal to one thousand million bits per second. Its symbol is Gbit/s, often written Gbps. It names the standard of wired local networking and, increasingly, of domestic fibre connections.

Gigabit Ethernet was standardised in 1998 for optical fibre and in 1999 for ordinary twisted-pair copper, and the copper version is what made it universal. It runs a hundred metres over the same cabling that carried the hundred-megabit standard before it, which meant buildings could be upgraded by replacing equipment rather than wiring. That single property fixed the gigabit as the default connection for a generation.

In octets a gigabit per second is 125 megaoctets per second. That is roughly the speed of a good mechanical hard drive and well below a modern solid-state drive, which is why gigabit networking is no longer the bottleneck it once was: the network can now outrun the storage at one end or the other in many common setups.

Domestic fibre services advertise a gigabit routinely, and the figure has become a marketing threshold more than a technical one. Practically no household can saturate it — a gigabit is enough for around two hundred simultaneous high-definition video streams — and the benefit in daily use is not throughput but the absence of congestion, which keeps latency low and steady.

Above the gigabit the ladder continues in the same steps. Ten-gigabit Ethernet is standard between servers and switches in data centres; twenty-five, forty, hundred and four-hundred-gigabit links join racks, buildings and cities. Each is a multiple of the same unit, and each is still counted in bits per second because that is what the optics and the copper actually carry.

Wireless has followed. The later wireless local network standards quote peak rates above a gigabit per second, though those figures assume a single device, ideal conditions and the full width of the channel. Real wireless throughput in a normal home is typically a third to a half of the advertised peak, and the gap widens with every additional device.

One gigabit per second equals 1,000,000,000 bits per second, 125 megaoctets per second, or about 0.9313 gibibits per second.