Conversion from 2 Pebibits per second to Megaoctets per second

Information about the Pebibit per second (Pibit/s)

The pebibit per second is a unit of data transfer rate equal to 1,024 tebibits per second, which is two to the fiftieth power bits per second. Its symbol is Pibit/s. It is the binary counterpart of the petabit per second, and the two differ by 12.6 per cent.

No deployed system runs at this rate, and the unit therefore describes either an aggregate or a laboratory result. Optical transmission records set on single fibres reach a petabit per second, and the binary figure for the same experiment is 12.6 per cent lower — a difference that matters when comparing results between papers that use different conventions.

Where the unit is genuinely appropriate is in describing structures built from powers of two. The total switching capacity of a very large network fabric, built from ports and buffers that are all binary, is a binary quantity divided by time, and reporting it in decimal units discards the arithmetic that produced it. The same applies to the summed memory bandwidth of a machine whose channel count is a power of two.

In octets a pebibit per second is 140,737,488,355,328, which is 128 tebioctets per second. That is the storage of a thousand large consumer drives moved every second, and it exists only as a total across many thousands of parallel paths inside a single facility.

The size of the discrepancy at this level is the argument for the whole IEC series in miniature. What began as a harmless 2.4 per cent at the kibibit is now an eighth, and it compounds by 2.4 per cent at every further step. A convention that was acceptable for small numbers becomes untenable for large ones, and the point of the binary prefixes is to make the distinction visible before that happens.

For a converter, the arithmetic is unremarkable: multiply or divide by 1,024 the appropriate number of times, and by eight to reach octets. What matters is that the tool does not silently substitute the decimal unit when it sees a value it cannot label precisely.

One pebibit per second equals 1,024 tebibits per second, 140,737,488,355,328 octets per second, or about 1.126 petabits per second.

Information about the Megaoctet per second (Mo/s)

The megaoctet per second is a unit of data transfer rate equal to one million octets per second, or eight megabits per second. Its symbol is Mo/s. It is the unit in which storage devices and their interfaces are rated, and the one a file manager shows while a copy is running.

Storage speeds fall naturally into this range. A mechanical hard drive sustains 100 to 250 megaoctets per second on sequential reads. A solid-state drive on the older interface reaches about 550, which is the limit of that interface rather than of the drive. A modern drive on the faster interface reaches several thousand, at which point the unit gives way to gigaoctets per second.

Interface speeds tell the same story from the other side. The successive versions of the universal serial bus have offered roughly 1.5, 60, 625 and 2,500 megaoctets per second at their nominal rates, and memory card standards have followed a similar path. A device is always limited by whichever of the two is slower, and matching them is the practical art of building a fast system.

For everyday sizes, one megaoctet per second transfers a photograph in a couple of seconds and a two-gigaoctet film in about half an hour. At 500 megaoctets per second the same film takes four seconds. That contrast explains why the perceived speed of a computer changed so completely when solid-state storage replaced mechanical drives, even though processors improved far less over the same period.

Sequential rates like these are the best case. Reading many small files instead of one large one costs far more, because each file requires locating its data and reading its record. A drive that sustains 500 megaoctets per second in sequence may manage only a few tens when copying a directory of thousands of small files, and that is where the difference between drive technologies is most visible.

The unit also describes the throughput of a busy network connection: a gigabit link delivers 125 megaoctets per second at best, so a fast local network and a fast drive are now comparable, and neither is obviously the limiting factor in a transfer.

One megaoctet per second equals 1,000,000 octets per second, 8 megabits per second, or about 0.9537 mebioctets per second.