Conversion from Megabits per second to Gigabits per second

Information about the Megabit per second (Mbit/s)

The megabit per second is a unit of data transfer rate equal to one million bits per second. Its symbol is Mbit/s, often written Mbps. It is the unit in which internet connections are sold, which makes it the data unit most people encounter by name.

Because it is a decimal million and not 1,048,576, the conversion to octets is exact and easy: one megabit per second is 125 kilooctets per second, so a hundred-megabit connection delivers about 12.5 megaoctets per second at best. Anyone who watches a file transfer and does the division has understood the entire relationship between how connections are advertised and how transfers are reported.

What a household actually needs is far below what it usually buys. Standard-definition video streaming uses about 3 megabits per second, high definition about 5, and ultra-high definition about 25. A video call is around 3 to 8. A large family watching four separate high-definition streams while somebody downloads a game is using perhaps 60 megabits per second, which a hundred-megabit connection handles comfortably.

The reason to buy more capacity than that is not peak speed but behaviour under load. A link that is near its limit develops queues, and queues add delay, which shows up as stutter in video calls and lag in games. A connection with generous headroom keeps its latency low, and that is a more noticeable improvement than a higher number on a speed test.

Wired local networks pass through this range on the way up. The original Ethernet ran at 10 megabits per second, its successor at 100, and both were the standard office connection for a decade each before gigabit replaced them. Wireless standards followed the same path with a lag, and both are now measured in hundreds of megabits or in gigabits.

Real throughput is always below the nominal rate. Protocol overhead takes 5 to 10 per cent on a wired link; a shared wireless channel loses much more, because the medium is divided between all the devices using it and interference forces retransmission. A connection advertised at 100 megabits per second measured at 90 over cable and 50 over a busy wireless network is behaving normally.

One megabit per second equals 1,000,000 bits per second, 125 kilooctets per second, or about 0.9537 mebibits per second.

Information about the Gigabit per second (Gbit/s)

The gigabit per second is a unit of data transfer rate equal to one thousand million bits per second. Its symbol is Gbit/s, often written Gbps. It names the standard of wired local networking and, increasingly, of domestic fibre connections.

Gigabit Ethernet was standardised in 1998 for optical fibre and in 1999 for ordinary twisted-pair copper, and the copper version is what made it universal. It runs a hundred metres over the same cabling that carried the hundred-megabit standard before it, which meant buildings could be upgraded by replacing equipment rather than wiring. That single property fixed the gigabit as the default connection for a generation.

In octets a gigabit per second is 125 megaoctets per second. That is roughly the speed of a good mechanical hard drive and well below a modern solid-state drive, which is why gigabit networking is no longer the bottleneck it once was: the network can now outrun the storage at one end or the other in many common setups.

Domestic fibre services advertise a gigabit routinely, and the figure has become a marketing threshold more than a technical one. Practically no household can saturate it — a gigabit is enough for around two hundred simultaneous high-definition video streams — and the benefit in daily use is not throughput but the absence of congestion, which keeps latency low and steady.

Above the gigabit the ladder continues in the same steps. Ten-gigabit Ethernet is standard between servers and switches in data centres; twenty-five, forty, hundred and four-hundred-gigabit links join racks, buildings and cities. Each is a multiple of the same unit, and each is still counted in bits per second because that is what the optics and the copper actually carry.

Wireless has followed. The later wireless local network standards quote peak rates above a gigabit per second, though those figures assume a single device, ideal conditions and the full width of the channel. Real wireless throughput in a normal home is typically a third to a half of the advertised peak, and the gap widens with every additional device.

One gigabit per second equals 1,000,000,000 bits per second, 125 megaoctets per second, or about 0.9313 gibibits per second.