Conversion from Gigapascals to Hectopascals

Information about the Gigapascal (GPa)

The gigapascal is a unit of pressure equal to a billion pascals, written GPa. It is a thousand megapascals and ten thousand bar. It is the unit in which materials science states stiffness rather than strength, and in which the pressures inside planets and inside high-pressure laboratories are described.

Elastic modulus is its principal use. Steel has a Young's modulus of about 200 gigapascals, copper 117, aluminium 70, ordinary glass 70, concrete around 30, timber along the grain 10 to 15, and rubber less than a tenth of one. Those numbers describe how much a material stretches under load, not when it breaks, and they explain why a steel beam of the same strength as an aluminium one still deflects less.

Diamond marks the top of the ordinary scale. Its modulus of roughly 1200 gigapascals is the highest of any natural material, which is why it is used to make anvils for high-pressure work: nothing else can push that hard without deforming first. Synthetic diamond is made industrially at about five gigapascals and high temperature, in presses built specifically to hold that pressure.

The interior of the earth is described in the same unit. Pressure at the base of the crust is around one gigapascal, at the boundary between mantle and core about 136, and at the centre of the planet roughly 360. Laboratory diamond anvil cells now reach and exceed the central value, which allows the behaviour of iron and silicates under planetary conditions to be studied directly rather than inferred.

For contrast, the deepest point in the ocean exerts only about 0.11 gigapascals. That comparison is worth keeping, because it shows how much larger geological pressures are than anything associated with water: the bottom of the Mariana Trench is a thousandth of the pressure at the centre of the earth.

Below the gigapascal, the megapascal describes strength, and above it there is little except stellar and theoretical physics. The terapascal appears mainly in the elastic modulus of carbon nanotubes and in the interiors of giant planets, so the gigapascal is effectively the top of the range that laboratories and engineers work in.

One gigapascal equals 1,000,000,000 pascals, 1000 megapascals, 10,000 bar, or about 145,000 pounds per square inch.

Information about the Hectopascal (hPa)

The hectopascal is a unit of pressure equal to one hundred pascals. Its symbol is hPa. It is exactly one millibar, and that identity is the whole reason it exists: when meteorology moved to SI units in the 1980s, the hectopascal let every barometer, chart and forecast keep its numbers unchanged while changing the name on them.

Weather is its home and almost its only use. Standard atmospheric pressure at sea level is 1013.25 hectopascals, a settled high-pressure system reads 1020 to 1035, and a deep Atlantic depression can fall below 950. Isobars on a synoptic chart are drawn at four-hectopascal intervals, so the spacing of the lines is a direct picture of how hard the wind will blow.

Storm intensity is reported the same way. The central pressure of a tropical cyclone is the single most quoted measure of its strength, and the lowest sea-level pressure ever recorded was 870 hectopascals in Typhoon Tip in 1979. A drop of a few tens of hectopascals over a day is enough to turn ordinary weather into a severe event.

Altitude changes the reading steadily. Near sea level pressure falls by roughly one hectopascal for every eight metres of height gained, which is why a barometric altimeter works at all and why a barometer at home responds to being carried upstairs. That gradient weakens with altitude, so the relationship holds only in the lowest few kilometres.

Aviation depends on the unit for safety. Pilots set their altimeters to a local pressure figure given in hectopascals so that everyone in the same airspace measures height from the same datum, and above a defined transition altitude all aircraft switch to the standard setting of 1013 hectopascals so that vertical separation is preserved regardless of the weather. North American practice uses inches of mercury for the same purpose, and the two must never be confused.

For conversion, one hectopascal is one millibar exactly, 0.1 kilopascals, and about 0.0295 inches of mercury. The last of those is the figure to watch, since a reading of 30 inches of mercury and one of 1016 hectopascals describe the same afternoon.

One hectopascal equals 100 pascals, 1 millibar, 0.1 kilopascals, or about 0.0295 inches of mercury.