Conversion from Gallons per second to Gallons per hour

Information about the Gallon per second (gal/s)

The gallon per second is a unit of volumetric flow rate equal to one imperial gallon passing a point every second. Its symbol is gal/s. The imperial gallon is 4.54609 litres, defined in 1824 as the volume of ten pounds of water at a stated temperature, so one gallon per second moves about four and a half litres — and, conveniently, about ten pounds — every second.

Firefighting is the discipline that works at this scale. A hose reel delivers a fraction of a gallon per second, a standard hose line 1 to 2, and a major pumping appliance 10 or more. British fire service practice quoted pump capacities in gallons per minute for most of the twentieth century, and the per-second figure is what a hydraulic calculation of pressure loss in the hose actually uses.

Large pumps and water mains reach it easily. A borehole pump on a farm might deliver half a gallon per second, a district water main several tens, and a river intake for a power station hundreds. Since the gallon of water weighs ten pounds, a flow in gallons per second converts to a mass flow in stones per second by dividing by 1.4, an arithmetic that older British engineering handbooks used freely.

Flood and drainage engineering in Britain used the unit until metrication. Culvert capacities, pumping station ratings and land drainage schemes were designed in gallons per second or per minute, and much of the surviving infrastructure still carries plates giving its capacity in those terms, which anyone assessing an old asset must convert with care.

The imperial gallon must be distinguished from the American one, which is 3.78541 litres — about twenty per cent smaller. A pump rated 10 gallons per second delivers 45.5 litres per second in Britain and 37.9 in the United States, a difference far too large to ignore in any calculation of capacity or of cost.

For scale, one gallon per second fills a domestic bath in about twenty-five seconds, and 0.22 gallons per second is one litre per second. A flow of ten gallons per second is a small stream, running at about 45 litres per second.

One gallon per second equals about 4.546 litres per second, about 0.004546 cubic metres per second, or about 1.201 US gallons per second.

Information about the Gallon per hour (gal/h)

The gallon per hour is a unit of volumetric flow rate equal to one imperial gallon passing a point every hour. Its symbol is gal/h, often abbreviated GPH. One imperial gallon is 4.54609 litres, so this unit describes the slow, sustained flows that matter over the length of a working day rather than a minute.

Fuel consumption is its most durable use. A boat's diesel engine burns 1 to 5 gallons per hour at cruising speed, a generator 0.5 to 2, and an agricultural tractor 2 to 4. Because such engines run at steady load for hours, the hourly figure multiplied by the hours of running gives the fuel bill directly, which is why boat and plant operators still think in these terms.

Oil-fired heating uses the unit for burner nozzles. A domestic oil boiler is fitted with a nozzle rated in gallons per hour — 0.5, 0.65 or 0.85 for a house — and that rating, multiplied by the calorific value of the oil, gives the heat output. Changing the nozzle changes the output, so the nozzle size on the burner label is effectively the rating of the appliance.

Water treatment and dosing are described the same way. A softener's regeneration flow, a chlorinator's feed rate and a chemical dosing pump on a cooling system are all set in gallons per hour, chosen so that the treated water leaves the plant with the concentration the process requires over a whole shift.

Older domestic water fittings carried the unit too. A header tank's fill rate, a cistern's refill and a slow-running standpipe were measured in gallons per hour in British practice, and the same figure told a householder how long a tank would take to recover after a bath had emptied it.

For scale, one gallon per hour is about 4.5 litres per hour, and 220 gallons per hour is about a cubic metre per hour. A rate of one gallon per hour would fill a domestic bath in about eighty hours, which is a fair reminder that this unit measures processes, not deliveries.

One gallon per hour equals about 4.546 litres per hour, about 0.004546 cubic metres per hour, or about 1.201 US gallons per hour.