| Square hands (sq hh) | Deciares (da) |
|---|---|
| 1 Square hand | 0.001032256 da |
| 2 Square hands | 0.002064512 da |
| 3 Square hands | 0.003096768 da |
| 4 Square hands | 0.004129024 da |
| 5 Square hands | 0.00516128 da |
| 10 Square hands | 0.01032256 da |
| 20 Square hands | 0.02064512 da |
| 25 Square hands | 0.0258064 da |
| 50 Square hands | 0.0516128 da |
| 100 Square hands | 0.1032256 da |
| Reference | Square hands (sq hh) | Deciares (da) |
|---|---|---|
| A sheet of A4 paper | 6.04211 sq hh | 0.006237 da |
| A tennis court | 25265.1 sq hh | 26.08 da |
| A football pitch | 691689 sq hh | 714 da |
| One hectare | 968752 sq hh | 1000 da |
| Central Park, New York | 330344411 sq hh | 341000 da |
The square hand is a unit of area equal to sixteen square inches, or 103.2256 square centimetres. Its symbol is sq hh. A hand is four inches, so a square hand is a square four inches on a side, roughly the area of an adult palm. It is a complete and consistent unit that almost nobody has ever needed, because the hand it derives from measures one thing only.
That one thing is horses. The height of a horse or pony is measured at the withers, the ridge between the shoulder blades, and it is given in hands almost everywhere in the world, including in countries that are otherwise entirely metric. A hand was fixed at four inches by an English statute of 1541 under Henry VIII, and the equestrian world has held to that figure ever since.
The notation contains a trap worth knowing. A horse described as 15.2 hands is not fifteen and two tenths but fifteen hands and two inches, which is 62 inches or 157.5 centimetres. The digit after the point runs from 0 to 3 and then rolls over, so 15.3 is followed by 16.0. Anyone converting a list of horse heights with ordinary decimal arithmetic will produce numbers that are wrong by up to three inches.
Where the boundary between pony and horse falls is decided by this measurement. Most classifications put it at 14.2 hands, which is 58 inches or 147.3 centimetres, and competition classes at every level are drawn on the same scale. Because a placing can depend on a fraction of an inch, official measurement is a regulated procedure carried out on a level surface by an approved measurer.
The area form has never followed the length into use. Body-derived units were invented for laying along things, the height of an animal, the length of a cloth, the depth of water, and not for enclosing ground, which is why the acre and the chain came from ploughing rather than from anatomy. A square hand is simply what appears when the rule for forming areas is applied to a unit that had no such purpose.
As a quantity it is easy enough to place. A hundred square centimetres is a large sticky note, a beer mat and a half, or the palm of a hand, which is the same comparison used to estimate burn area in first aid. Sixteen square hands make a square foot, and 2304 of them make a square yard.
One square hand equals 16 square inches, about 103.23 square centimetres, or about 0.0103 square metres.
The deciare is a unit of area equal to one tenth of an are, or ten square metres. Its symbol is da. It completes the decimal ladder that the French metric law of 1795 built around the are, alongside the centiare below it and the hectare above, but unlike either of those it never found a job and is today the least used member of the family.
Ten square metres is an easily pictured quantity. It is a small bathroom, a single bedroom in a modest flat, or four fifths of a car parking space. It is the floor of a garden shed, the area a market trader is allotted at a fair, or the footprint of a large dining table with chairs pushed back. Nothing about the size is obscure; only the name is.
The reason it failed is structural. Land registration adopted a three-column system running hectare, are and centiare, each step a factor of one hundred, which mirrors how areas actually behave: squaring a tenfold change in length produces a hundredfold change in area. A tenth of an are sits between two columns and belongs to neither, so no register ever needed a place for it.
Its symbol makes matters worse. In the International System, da is the prefix symbol for deca, so a reader meeting da in a technical document is far more likely to take it as the start of a compound like dam or daN than as a unit in its own right. The decare, ten times larger, is written daa, which does nothing to help.
Where the quantity does need naming, ordinary metric notation handles it without effort. Ten square metres is written 10 m², which is shorter than one deciare, needs no explanation, and sorts correctly beside every other figure on a plan or in a contract.
The unit therefore survives almost entirely in conversion tables and in teaching material that runs through the complete prefix ladder. Encountering it in a real document usually means the document is old, translated from an older source, or reproducing a table rather than making a measurement, and converting it to square metres at once is the safe response.
One deciare equals 10 square metres, 0.1 ares, 0.001 hectares, or about 107.6 square feet.