| Centiares (ca) | Deciares (da) |
|---|---|
| 1 Centiare | 0.1 da |
| 2 Centiares | 0.2 da |
| 3 Centiares | 0.3 da |
| 4 Centiares | 0.4 da |
| 5 Centiares | 0.5 da |
| 10 Centiares | 1 da |
| 20 Centiares | 2 da |
| 25 Centiares | 2.5 da |
| 50 Centiares | 5 da |
| 100 Centiares | 10 da |
| Reference | Centiares (ca) | Deciares (da) |
|---|---|---|
| A sheet of A4 paper | 0.06237 ca | 0.006237 da |
| A tennis court | 260.8 ca | 26.08 da |
| A football pitch | 7140 ca | 714 da |
| One hectare | 10000 ca | 1000 da |
| Central Park, New York | 3410000 ca | 341000 da |
The centiare is a unit of area equal to one hundredth of an are, which makes it exactly one square metre. Its symbol is ca. It is the only unit in common use that is an exact duplicate of another under a different name, and the reason it exists at all is a matter of bookkeeping rather than of measurement.
When the French metric law of 1795 established the are as the decimal unit of land, it created a full ladder around it: the hectare above and the centiare below. Land registries then adopted a three-column format, recording every parcel as so many hectares, so many ares and so many centiares. The last column needed a name, and the square metre, though identical, did not fit the pattern.
That format is still in force. French, Belgian, Luxembourgish and Dutch land registers write parcel areas as three numbers in sequence, so 1 ha 25 a 30 ca means 12,530 square metres. The middle and last figures never exceed 99, which makes the notation self-checking: a value like 1 ha 130 a is malformed and signals a transcription error before anyone has to do arithmetic.
Reading it is a matter of place value. Each hectare is 10,000 square metres, each are is 100, and each centiare is one, so the three columns simply spell out a number in base one hundred. A notary's figure of 0 ha 04 a 62 ca is 462 square metres, and a surveyor's plan showing the same plot would print 462 m² without further comment.
Outside the land registry the centiare has no life. Nobody specifies a floor, a wall or a plot of ground in centiares when the square metre says the same thing with a symbol everyone recognises, and no branch of science or engineering has ever adopted it. It is a unit that exists to fill a column.
The one hazard is the symbol. In many documents ca is an abbreviation for the Latin circa, meaning approximately, so a figure that reads ca 400 could mean 400 centiares or about 400 of something else entirely. In land records the position of the number resolves it; in running text, converting to square metres removes the ambiguity for good.
One centiare equals exactly 1 square metre, 0.01 ares, or about 10.764 square feet.
The deciare is a unit of area equal to one tenth of an are, or ten square metres. Its symbol is da. It completes the decimal ladder that the French metric law of 1795 built around the are, alongside the centiare below it and the hectare above, but unlike either of those it never found a job and is today the least used member of the family.
Ten square metres is an easily pictured quantity. It is a small bathroom, a single bedroom in a modest flat, or four fifths of a car parking space. It is the floor of a garden shed, the area a market trader is allotted at a fair, or the footprint of a large dining table with chairs pushed back. Nothing about the size is obscure; only the name is.
The reason it failed is structural. Land registration adopted a three-column system running hectare, are and centiare, each step a factor of one hundred, which mirrors how areas actually behave: squaring a tenfold change in length produces a hundredfold change in area. A tenth of an are sits between two columns and belongs to neither, so no register ever needed a place for it.
Its symbol makes matters worse. In the International System, da is the prefix symbol for deca, so a reader meeting da in a technical document is far more likely to take it as the start of a compound like dam or daN than as a unit in its own right. The decare, ten times larger, is written daa, which does nothing to help.
Where the quantity does need naming, ordinary metric notation handles it without effort. Ten square metres is written 10 m², which is shorter than one deciare, needs no explanation, and sorts correctly beside every other figure on a plan or in a contract.
The unit therefore survives almost entirely in conversion tables and in teaching material that runs through the complete prefix ladder. Encountering it in a real document usually means the document is old, translated from an older source, or reproducing a table rather than making a measurement, and converting it to square metres at once is the safe response.
One deciare equals 10 square metres, 0.1 ares, 0.001 hectares, or about 107.6 square feet.