| Square decameters (dam²) | Deciares (da) |
|---|---|
| 1 Square decameter | 10 da |
| 2 Square decameters | 20 da |
| 3 Square decameters | 30 da |
| 4 Square decameters | 40 da |
| 5 Square decameters | 50 da |
| 10 Square decameters | 100 da |
| 20 Square decameters | 200 da |
| 25 Square decameters | 250 da |
| 50 Square decameters | 500 da |
| 100 Square decameters | 1000 da |
| Reference | Square decameters (dam²) | Deciares (da) |
|---|---|---|
| A sheet of A4 paper | 0.0006237 dam² | 0.006237 da |
| A tennis court | 2.608 dam² | 26.08 da |
| A football pitch | 71.4 dam² | 714 da |
| One hectare | 100 dam² | 1000 da |
| Central Park, New York | 34100 dam² | 341000 da |
The square decametre is a unit of area equal to one hundred square metres. It is written dam², and it is the area of a square ten metres on a side, since a decametre is ten metres. It is exactly the same quantity as the are, and the choice between the two names is a choice between strict metric grammar and two centuries of habit.
The International System is built from coherent units, meaning every derived unit is a product or quotient of base units with no extra factors. Squaring a prefixed length gives a perfectly coherent area, so the square decametre needs no special permission to exist. The are, by contrast, is listed as a non-SI unit accepted for use with the SI, tolerated for land measurement rather than derived from anything.
Despite that formal advantage, the square decametre lost decisively. The are was already in every French land register when the modern system was codified, and a register does not change its columns for a matter of notation. The result is that the correct SI form is almost never written, and its accepted non-SI equivalent is what appears on deeds across half of Europe.
The quantity itself is a useful one to be able to picture, whichever name is used. A hundred square metres is a square ten metres on a side: a generous garden, the ground floor of a small house, a market stall pitch, or a large classroom. It is the last area a person can pace out accurately without instruments, and it is the natural size for describing a plot rather than a field.
Where the symbol does appear, the exponent must be read carefully. The string dam already means decametre, a length, so dam² and dam differ by an entire dimension, and a dropped superscript turns an area into a distance. Software that strips formatting from tables is a common cause of exactly that error.
For any practical purpose, converting is the right response. Multiply by a hundred for square metres, divide by a hundred for hectares, and the resulting figure will match whatever else is on the page. One square decametre is one are, and both are one hundred square metres, so nothing is lost in either direction.
One square decametre equals 100 square metres, 1 are, 0.01 hectares, or about 1076.4 square feet.
The deciare is a unit of area equal to one tenth of an are, or ten square metres. Its symbol is da. It completes the decimal ladder that the French metric law of 1795 built around the are, alongside the centiare below it and the hectare above, but unlike either of those it never found a job and is today the least used member of the family.
Ten square metres is an easily pictured quantity. It is a small bathroom, a single bedroom in a modest flat, or four fifths of a car parking space. It is the floor of a garden shed, the area a market trader is allotted at a fair, or the footprint of a large dining table with chairs pushed back. Nothing about the size is obscure; only the name is.
The reason it failed is structural. Land registration adopted a three-column system running hectare, are and centiare, each step a factor of one hundred, which mirrors how areas actually behave: squaring a tenfold change in length produces a hundredfold change in area. A tenth of an are sits between two columns and belongs to neither, so no register ever needed a place for it.
Its symbol makes matters worse. In the International System, da is the prefix symbol for deca, so a reader meeting da in a technical document is far more likely to take it as the start of a compound like dam or daN than as a unit in its own right. The decare, ten times larger, is written daa, which does nothing to help.
Where the quantity does need naming, ordinary metric notation handles it without effort. Ten square metres is written 10 m², which is shorter than one deciare, needs no explanation, and sorts correctly beside every other figure on a plan or in a contract.
The unit therefore survives almost entirely in conversion tables and in teaching material that runs through the complete prefix ladder. Encountering it in a real document usually means the document is old, translated from an older source, or reproducing a table rather than making a measurement, and converting it to square metres at once is the safe response.
One deciare equals 10 square metres, 0.1 ares, 0.001 hectares, or about 107.6 square feet.