Conversion from 5 Decipascals to Decapascals

Information about the Decipascal (dPa)

The decipascal is a unit of pressure equal to one tenth of a pascal. Its symbol is dPa. It belongs to the group of metric prefixes that exist because the system is regular rather than because anyone asked for them: deci, centi, deca and hecto fill the gaps between the thousand-step prefixes, and of those four only hecto found a permanent home in pressure, in the hectopascal of weather reports.

That regularity is the point of the metric system rather than an accident of it. Every prefix from yocto to yotta applies to every unit, so the decipascal is defined whether or not anyone writes it. The alternative would be a system in which some combinations are legal and others are not, and users would then have to memorise a table of exceptions instead of a single rule.

In practice pressure work skips from the pascal to the hectopascal or kilopascal, and the four intermediate prefixes go unused. There is a reason for that beyond habit. The thousand-step prefixes — milli, kilo, mega — line up with how numbers are grouped in writing, so a value in kilopascals is read off a value in pascals by moving the digit grouping, not by counting decimal places. Deci and centi break that alignment.

The decipascal does have a natural size, though. A tenth of a pascal is roughly the pressure of a single sheet of thin paper laid on a table, or the difference in air pressure over about a centimetre of height. It is the pressure a moth exerts on a windowpane, and about a hundredth of the pressure difference across a closed interior door in a ventilated building.

Where such pressures need writing down, the convention is to use the pascal with a decimal: an anemometer calibration might record 0.4 pascals rather than 4 decipascals, and a ventilation specification 50 pascals rather than 500 decipascals. The number is the same and the pascal keeps the page consistent with every other reading.

The unit is still perfectly valid, and a converter has to handle it, because it turns up in older instrument manuals, in occasional national standards, and wherever an author has decided that a figure reads better with one digit before the point than with three after it.

One decipascal equals 0.1 pascals, 100 millipascals, 0.001 hectopascals, or about 0.0000145 pounds per square inch.

Information about the Decapascal (daPa)

The decapascal is a unit of pressure equal to ten pascals. Its symbol is daPa. Deca is the least used prefix in the metric system almost everywhere, but the decapascal is an exception, because one clinical discipline adopted it and has kept it: audiology measures the pressure inside the middle ear in decapascals.

Tympanometry is the test in question. A probe seals the ear canal and varies the air pressure in it while measuring how much sound the eardrum reflects, and the resulting curve is plotted against pressure in decapascals. The sweep runs from about plus 200 to minus 400, and the position of the peak shows the pressure at which the eardrum moves most freely, which is normally the pressure of the middle ear itself.

That single graph carries a great deal of clinical information. A peak near zero means the middle ear is at the same pressure as the room, which is the healthy state. A peak displaced towards minus 200 or beyond suggests the Eustachian tube is not equalising properly, and a flat curve with no peak at all suggests fluid behind the eardrum. Each of those readings is a position on a decapascal scale.

The unit was chosen for the same reason the hectopascal was chosen in meteorology. Middle-ear pressure had long been recorded in millimetres of water, and one millimetre of water is 0.98 decapascals, so switching to the metric unit left every clinical number and every published reference range almost unchanged. A change of unit that shifts the figures by two per cent is one that practitioners will actually accept.

Outside audiology the decapascal is essentially unused. Ventilation and building airtightness work at similar pressures, an airtightness test being run at fifty pascals, but those figures are written in pascals, and everything above them moves to hectopascals or kilopascals. The gap between one and a hundred pascals is otherwise unclaimed.

For scale, ten pascals is the pressure a light breeze exerts on a wall, or the difference between the two ends of a well-sealed corridor when a door opens. It is also roughly the pressure change from riding a lift up one floor, which is why ears sometimes need clearing in a tall building.

One decapascal equals 10 pascals, 0.1 hectopascals, about 1.02 millimetres of water, or about 0.00145 pounds per square inch.