Conversion from Decipascals to Kilopascals

Information about the Decipascal (dPa)

The decipascal is a unit of pressure equal to one tenth of a pascal. Its symbol is dPa. It belongs to the group of metric prefixes that exist because the system is regular rather than because anyone asked for them: deci, centi, deca and hecto fill the gaps between the thousand-step prefixes, and of those four only hecto found a permanent home in pressure, in the hectopascal of weather reports.

That regularity is the point of the metric system rather than an accident of it. Every prefix from yocto to yotta applies to every unit, so the decipascal is defined whether or not anyone writes it. The alternative would be a system in which some combinations are legal and others are not, and users would then have to memorise a table of exceptions instead of a single rule.

In practice pressure work skips from the pascal to the hectopascal or kilopascal, and the four intermediate prefixes go unused. There is a reason for that beyond habit. The thousand-step prefixes — milli, kilo, mega — line up with how numbers are grouped in writing, so a value in kilopascals is read off a value in pascals by moving the digit grouping, not by counting decimal places. Deci and centi break that alignment.

The decipascal does have a natural size, though. A tenth of a pascal is roughly the pressure of a single sheet of thin paper laid on a table, or the difference in air pressure over about a centimetre of height. It is the pressure a moth exerts on a windowpane, and about a hundredth of the pressure difference across a closed interior door in a ventilated building.

Where such pressures need writing down, the convention is to use the pascal with a decimal: an anemometer calibration might record 0.4 pascals rather than 4 decipascals, and a ventilation specification 50 pascals rather than 500 decipascals. The number is the same and the pascal keeps the page consistent with every other reading.

The unit is still perfectly valid, and a converter has to handle it, because it turns up in older instrument manuals, in occasional national standards, and wherever an author has decided that a figure reads better with one digit before the point than with three after it.

One decipascal equals 0.1 pascals, 100 millipascals, 0.001 hectopascals, or about 0.0000145 pounds per square inch.

Information about the Kilopascal (kPa)

The kilopascal is a unit of pressure equal to one thousand pascals. Its symbol is kPa. It is a hundredth of a bar and ten hectopascals, and it is the coherent SI unit that engineering was meant to adopt when the pascal proved too small to write comfortably. Standard atmospheric pressure is 101.325 kilopascals.

Tyres are where most people meet it. Canada, Australia, New Zealand and much of Asia state recommended tyre pressures in kilopascals, so a car door placard reads 220 or 240 rather than 32 or 35 pounds per square inch. The two scales sit side by side on most modern gauges, and the conversion is close to seven kilopascals to the pound per square inch.

Civil engineering uses it for loads on ground and structure. The bearing capacity of a soil is quoted in kilopascals, a firm clay allowing perhaps 150 and a soft one much less, and wind loading on a facade is calculated in the same unit. Because a kilopascal is also a kilonewton per square metre, structural calculations move between force and pressure without a conversion factor.

Medicine uses it in one important place. Arterial blood gases are reported in kilopascals in Britain, Ireland and much of Europe, where a healthy oxygen partial pressure is eleven to thirteen, while the United States reports the same measurement in millimetres of mercury as eighty to a hundred. The two numbers describe identical blood, and a clinician reading a foreign chart must know which convention it follows.

Vacuum work counts downward in it. A rough vacuum is a few kilopascals absolute, a domestic vacuum cleaner pulls perhaps twenty kilopascals below atmospheric, and freeze-drying operates well under one. Stating vacuum as an absolute pressure in kilopascals avoids the ambiguity of describing it as a negative gauge pressure.

Its awkwardness is only rhetorical. A hundred kilopascals is exactly one bar and reads less neatly, which is why the bar has held on in Europe despite decades of official preference for the pascal. Where the kilopascal has won, as on Canadian and Australian tyre placards, it has done so because the number is printed rather than spoken.

One kilopascal equals 1000 pascals, 0.01 bar, 10 hectopascals, or about 0.145 pounds per square inch.