Conversion from 4 Pascals to Decipascals

Information about the Pascal (Pa)

The pascal is the SI unit of pressure, written Pa. It is defined as one newton of force spread over one square metre, and it is named after Blaise Pascal, whose experiments with barometers in the 1640s established that air has weight and that its pressure falls with altitude. The General Conference on Weights and Measures adopted the name in 1971.

It is a remarkably small unit. Atmospheric pressure at sea level is 101,325 pascals, so the pressure everyone lives under is a six-figure number, and almost every practical use of the unit therefore carries a prefix. That awkwardness is not a design fault but a consequence of coherence: the newton and the square metre were fixed first, and the pascal is whatever falls out of dividing one by the other.

Acoustics is the field where bare pascals are natural. The reference pressure for the decibel scale is twenty micropascals, taken as the quietest sound a healthy young ear can detect, and ordinary conversation is around 0.02 pascals of sound pressure. The threshold of pain sits near 63 pascals, so the entire range of human hearing spans about six orders of magnitude in this unit.

Everyday objects give a sense of the scale. A sheet of office paper lying flat presses on the desk with about 0.8 pascals. A gentle breeze exerts a few pascals on a wall, and the pressure difference that drives ventilation through a building is typically between ten and fifty. Anything a person can feel as force is already in the thousands.

Prefixed forms carry the real work. Weather uses hectopascals, which are numerically identical to the older millibars, so a forecast reading of 1013 needed no relearning. Engineering uses kilopascals for tyre and fluid pressures, and materials science uses megapascals and gigapascals for strength and stiffness, where one megapascal is one newton per square millimetre.

The pascal also appears wherever a stress rather than a pressure is meant, since the two have the same dimensions. Young's modulus, yield strength and shear stress are all quoted in pascals or their multiples, which is why a single unit spans the pressure in a tyre and the stiffness of steel.

One pascal equals 1 newton per square metre, 0.01 millibars, about 0.0000099 atmospheres, or about 0.000145 pounds per square inch.

Information about the Decipascal (dPa)

The decipascal is a unit of pressure equal to one tenth of a pascal. Its symbol is dPa. It belongs to the group of metric prefixes that exist because the system is regular rather than because anyone asked for them: deci, centi, deca and hecto fill the gaps between the thousand-step prefixes, and of those four only hecto found a permanent home in pressure, in the hectopascal of weather reports.

That regularity is the point of the metric system rather than an accident of it. Every prefix from yocto to yotta applies to every unit, so the decipascal is defined whether or not anyone writes it. The alternative would be a system in which some combinations are legal and others are not, and users would then have to memorise a table of exceptions instead of a single rule.

In practice pressure work skips from the pascal to the hectopascal or kilopascal, and the four intermediate prefixes go unused. There is a reason for that beyond habit. The thousand-step prefixes — milli, kilo, mega — line up with how numbers are grouped in writing, so a value in kilopascals is read off a value in pascals by moving the digit grouping, not by counting decimal places. Deci and centi break that alignment.

The decipascal does have a natural size, though. A tenth of a pascal is roughly the pressure of a single sheet of thin paper laid on a table, or the difference in air pressure over about a centimetre of height. It is the pressure a moth exerts on a windowpane, and about a hundredth of the pressure difference across a closed interior door in a ventilated building.

Where such pressures need writing down, the convention is to use the pascal with a decimal: an anemometer calibration might record 0.4 pascals rather than 4 decipascals, and a ventilation specification 50 pascals rather than 500 decipascals. The number is the same and the pascal keeps the page consistent with every other reading.

The unit is still perfectly valid, and a converter has to handle it, because it turns up in older instrument manuals, in occasional national standards, and wherever an author has decided that a figure reads better with one digit before the point than with three after it.

One decipascal equals 0.1 pascals, 100 millipascals, 0.001 hectopascals, or about 0.0000145 pounds per square inch.