Conversion from 25 Pascals to Megapascals

Information about the Pascal (Pa)

The pascal is the SI unit of pressure, written Pa. It is defined as one newton of force spread over one square metre, and it is named after Blaise Pascal, whose experiments with barometers in the 1640s established that air has weight and that its pressure falls with altitude. The General Conference on Weights and Measures adopted the name in 1971.

It is a remarkably small unit. Atmospheric pressure at sea level is 101,325 pascals, so the pressure everyone lives under is a six-figure number, and almost every practical use of the unit therefore carries a prefix. That awkwardness is not a design fault but a consequence of coherence: the newton and the square metre were fixed first, and the pascal is whatever falls out of dividing one by the other.

Acoustics is the field where bare pascals are natural. The reference pressure for the decibel scale is twenty micropascals, taken as the quietest sound a healthy young ear can detect, and ordinary conversation is around 0.02 pascals of sound pressure. The threshold of pain sits near 63 pascals, so the entire range of human hearing spans about six orders of magnitude in this unit.

Everyday objects give a sense of the scale. A sheet of office paper lying flat presses on the desk with about 0.8 pascals. A gentle breeze exerts a few pascals on a wall, and the pressure difference that drives ventilation through a building is typically between ten and fifty. Anything a person can feel as force is already in the thousands.

Prefixed forms carry the real work. Weather uses hectopascals, which are numerically identical to the older millibars, so a forecast reading of 1013 needed no relearning. Engineering uses kilopascals for tyre and fluid pressures, and materials science uses megapascals and gigapascals for strength and stiffness, where one megapascal is one newton per square millimetre.

The pascal also appears wherever a stress rather than a pressure is meant, since the two have the same dimensions. Young's modulus, yield strength and shear stress are all quoted in pascals or their multiples, which is why a single unit spans the pressure in a tyre and the stiffness of steel.

One pascal equals 1 newton per square metre, 0.01 millibars, about 0.0000099 atmospheres, or about 0.000145 pounds per square inch.

Information about the Megapascal (MPa)

The megapascal is a unit of pressure equal to one million pascals, written MPa. It is ten bar, and it is exactly one newton per square millimetre. That last identity is the reason the unit dominates engineering: a stress calculated from a force in newtons and an area in square millimetres comes out in megapascals with no conversion at all.

Materials strength is stated in it almost universally. A common structural steel yields at 355 megapascals, high-strength alloy steels at over a thousand, aluminium alloys between 200 and 500, and structural concrete at 25 to 50 in compression. Because those numbers are what a designer compares against a calculated stress, the megapascal is the unit in which most of the built world is specified.

Structural drawings often write N/mm² instead, and the two are the same. Some national codes prefer one form and some the other, but a plate marked 355 N/mm² and one marked 355 MPa carry identical steel. Knowing that they are the same unit removes what looks like a discrepancy between drawings from different countries.

Hydraulics works at these pressures too. Construction machinery runs at twenty to thirty-five megapascals, industrial presses higher, and water-jet cutting reaches four hundred, at which pressure a stream of water a fraction of a millimetre across will cut steel. Pressure vessels, pipelines and hydrogen storage are all designed and tested against figures in this range.

Above the megapascal, the gigapascal takes over for stiffness rather than strength. Young's modulus for steel is about 200 gigapascals, for aluminium 70 and for concrete 30, and those numbers describe how much a material deflects rather than when it breaks. Keeping strength in megapascals and stiffness in gigapascals is a convention that makes the two easy to tell apart at a glance.

For conversion, one megapascal is ten bar, 145 pounds per square inch, and just under ten atmospheres. The last comparison is worth holding: a pressure of one megapascal is about ten times what the air outside exerts, which puts even modest industrial pressures in a useful human perspective.

One megapascal equals 1,000,000 pascals, 10 bar, 1 newton per square millimetre, or about 145 pounds per square inch.