Conversion from Megapascals to Newtons per square meter

Information about the Megapascal (MPa)

The megapascal is a unit of pressure equal to one million pascals, written MPa. It is ten bar, and it is exactly one newton per square millimetre. That last identity is the reason the unit dominates engineering: a stress calculated from a force in newtons and an area in square millimetres comes out in megapascals with no conversion at all.

Materials strength is stated in it almost universally. A common structural steel yields at 355 megapascals, high-strength alloy steels at over a thousand, aluminium alloys between 200 and 500, and structural concrete at 25 to 50 in compression. Because those numbers are what a designer compares against a calculated stress, the megapascal is the unit in which most of the built world is specified.

Structural drawings often write N/mm² instead, and the two are the same. Some national codes prefer one form and some the other, but a plate marked 355 N/mm² and one marked 355 MPa carry identical steel. Knowing that they are the same unit removes what looks like a discrepancy between drawings from different countries.

Hydraulics works at these pressures too. Construction machinery runs at twenty to thirty-five megapascals, industrial presses higher, and water-jet cutting reaches four hundred, at which pressure a stream of water a fraction of a millimetre across will cut steel. Pressure vessels, pipelines and hydrogen storage are all designed and tested against figures in this range.

Above the megapascal, the gigapascal takes over for stiffness rather than strength. Young's modulus for steel is about 200 gigapascals, for aluminium 70 and for concrete 30, and those numbers describe how much a material deflects rather than when it breaks. Keeping strength in megapascals and stiffness in gigapascals is a convention that makes the two easy to tell apart at a glance.

For conversion, one megapascal is ten bar, 145 pounds per square inch, and just under ten atmospheres. The last comparison is worth holding: a pressure of one megapascal is about ten times what the air outside exerts, which puts even modest industrial pressures in a useful human perspective.

One megapascal equals 1,000,000 pascals, 10 bar, 1 newton per square millimetre, or about 145 pounds per square inch.

Information about the Newton per square meter (N/m²)

The newton per square metre is a unit of pressure equal to one pascal. Its symbol is N/m². The two are not merely equivalent but identical: the pascal is the name given to this combination, and before the General Conference on Weights and Measures adopted that name in 1971 the SI unit of pressure had no name at all and was written out in full.

Both forms survive because they do different work on the page. The pascal is compact and reads as a unit in its own right, which suits a measurement. The newton per square metre shows its dimensions, which suits a calculation, because it makes visible that multiplying by an area in square metres will give a force in newtons.

Structural engineering leans on the second property constantly. Floor loads are specified in kilonewtons per square metre, with about 1.5 for a dwelling, 3 for an office and 5 for a place of assembly, and multiplying that figure by the floor area gives directly the load in kilonewtons that the beams must carry. Written as kilopascals the same numbers would be correct but would hide the step.

Snow and wind follow the same convention. Snow load is given in kilonewtons per square metre, from a few tenths in a mild climate to several in the mountains, and wind pressure on a facade likewise. Because those loads are combined with dead weight, which is naturally a force, keeping everything in newtons avoids the need to convert anything.

The construction repeats one prefix down. A newton per square millimetre is exactly one megapascal, which is why material strengths appear on drawings as N/mm² as often as MPa. The pattern is worth recognising: whenever a document writes force over area rather than naming a pressure unit, it is because the writer expects the reader to multiply.

Nothing else distinguishes the two forms. Any value in newtons per square metre can be written as pascals without change, and any conversion table treats them as one entry. The choice is a matter of what the number is about to be used for.

One newton per square metre equals 1 pascal, 0.01 millibars, 0.00001 bar, or about 0.000145 pounds per square inch.