Conversion from 25 Gallons per second to Cubic inches per second

Information about the Gallon per second (gal/s)

The gallon per second is a unit of volumetric flow rate equal to one imperial gallon passing a point every second. Its symbol is gal/s. The imperial gallon is 4.54609 litres, defined in 1824 as the volume of ten pounds of water at a stated temperature, so one gallon per second moves about four and a half litres — and, conveniently, about ten pounds — every second.

Firefighting is the discipline that works at this scale. A hose reel delivers a fraction of a gallon per second, a standard hose line 1 to 2, and a major pumping appliance 10 or more. British fire service practice quoted pump capacities in gallons per minute for most of the twentieth century, and the per-second figure is what a hydraulic calculation of pressure loss in the hose actually uses.

Large pumps and water mains reach it easily. A borehole pump on a farm might deliver half a gallon per second, a district water main several tens, and a river intake for a power station hundreds. Since the gallon of water weighs ten pounds, a flow in gallons per second converts to a mass flow in stones per second by dividing by 1.4, an arithmetic that older British engineering handbooks used freely.

Flood and drainage engineering in Britain used the unit until metrication. Culvert capacities, pumping station ratings and land drainage schemes were designed in gallons per second or per minute, and much of the surviving infrastructure still carries plates giving its capacity in those terms, which anyone assessing an old asset must convert with care.

The imperial gallon must be distinguished from the American one, which is 3.78541 litres — about twenty per cent smaller. A pump rated 10 gallons per second delivers 45.5 litres per second in Britain and 37.9 in the United States, a difference far too large to ignore in any calculation of capacity or of cost.

For scale, one gallon per second fills a domestic bath in about twenty-five seconds, and 0.22 gallons per second is one litre per second. A flow of ten gallons per second is a small stream, running at about 45 litres per second.

One gallon per second equals about 4.546 litres per second, about 0.004546 cubic metres per second, or about 1.201 US gallons per second.

Information about the Cubic inch per second (in³/s)

The cubic inch per second is a unit of volumetric flow rate equal to one cubic inch passing a point every second. Its symbol is in³/s. A cubic inch is 16.387 cubic centimetres, a little over a tablespoon, so this unit describes the modest but visible flows of imperial engineering practice.

Hydraulics is where it survives most strongly. American hydraulic pumps and cylinders are still catalogued in inches, and a cylinder's speed follows directly from the flow divided by the piston area: a 2-inch bore cylinder has an area of 3.14 square inches, so 31.4 cubic inches per second extends it at 10 inches per second. Working in inches throughout avoids converting the bore, the stroke and the flow separately.

Machining uses the same idea for material removal. A milling cutter taking a 0.1-inch depth at 0.5 inch width and 20 inches per minute of feed removes one cubic inch per minute, and a modern machining centre roughing aluminium can exceed twenty. Tool manufacturers publish removal rates in these units because their customers' machines are dimensioned that way.

Small engines and pumps carry the unit too. An engine's displacement in cubic inches, multiplied by its speed, gives the air it swallows: a 350 cubic inch V8 at 3,000 revolutions per minute ingests 525,000 cubic inches a minute, or about 8,750 per second, ideal efficiency assumed. The old American habit of naming engines by cubic inches is the same measurement standing still rather than flowing.

Metering and dispensing in imperial industries follow. Adhesive dispensers, lubricators and grease systems on American plant are specified in cubic inches per second or per minute, and a shot of grease from an automatic lubricator is quoted in cubic inches per cycle, which the cycle time converts into a rate.

For a sense of scale, 61 cubic inches per second is about a litre per second, and one cubic inch per second fills a US gallon in a little under four minutes. That is roughly the rate of a garden tap opened a quarter turn, which makes the unit easy to picture despite its unfamiliarity outside the imperial trades.

One cubic inch per second equals about 16.39 cubic centimetres per second, 0.01639 litres per second, or about 0.2597 US gallons per minute.