Conversion from 2 Pebibits per second to Gigabits per second

Information about the Pebibit per second (Pibit/s)

The pebibit per second is a unit of data transfer rate equal to 1,024 tebibits per second, which is two to the fiftieth power bits per second. Its symbol is Pibit/s. It is the binary counterpart of the petabit per second, and the two differ by 12.6 per cent.

No deployed system runs at this rate, and the unit therefore describes either an aggregate or a laboratory result. Optical transmission records set on single fibres reach a petabit per second, and the binary figure for the same experiment is 12.6 per cent lower — a difference that matters when comparing results between papers that use different conventions.

Where the unit is genuinely appropriate is in describing structures built from powers of two. The total switching capacity of a very large network fabric, built from ports and buffers that are all binary, is a binary quantity divided by time, and reporting it in decimal units discards the arithmetic that produced it. The same applies to the summed memory bandwidth of a machine whose channel count is a power of two.

In octets a pebibit per second is 140,737,488,355,328, which is 128 tebioctets per second. That is the storage of a thousand large consumer drives moved every second, and it exists only as a total across many thousands of parallel paths inside a single facility.

The size of the discrepancy at this level is the argument for the whole IEC series in miniature. What began as a harmless 2.4 per cent at the kibibit is now an eighth, and it compounds by 2.4 per cent at every further step. A convention that was acceptable for small numbers becomes untenable for large ones, and the point of the binary prefixes is to make the distinction visible before that happens.

For a converter, the arithmetic is unremarkable: multiply or divide by 1,024 the appropriate number of times, and by eight to reach octets. What matters is that the tool does not silently substitute the decimal unit when it sees a value it cannot label precisely.

One pebibit per second equals 1,024 tebibits per second, 140,737,488,355,328 octets per second, or about 1.126 petabits per second.

Information about the Gigabit per second (Gbit/s)

The gigabit per second is a unit of data transfer rate equal to one thousand million bits per second. Its symbol is Gbit/s, often written Gbps. It names the standard of wired local networking and, increasingly, of domestic fibre connections.

Gigabit Ethernet was standardised in 1998 for optical fibre and in 1999 for ordinary twisted-pair copper, and the copper version is what made it universal. It runs a hundred metres over the same cabling that carried the hundred-megabit standard before it, which meant buildings could be upgraded by replacing equipment rather than wiring. That single property fixed the gigabit as the default connection for a generation.

In octets a gigabit per second is 125 megaoctets per second. That is roughly the speed of a good mechanical hard drive and well below a modern solid-state drive, which is why gigabit networking is no longer the bottleneck it once was: the network can now outrun the storage at one end or the other in many common setups.

Domestic fibre services advertise a gigabit routinely, and the figure has become a marketing threshold more than a technical one. Practically no household can saturate it — a gigabit is enough for around two hundred simultaneous high-definition video streams — and the benefit in daily use is not throughput but the absence of congestion, which keeps latency low and steady.

Above the gigabit the ladder continues in the same steps. Ten-gigabit Ethernet is standard between servers and switches in data centres; twenty-five, forty, hundred and four-hundred-gigabit links join racks, buildings and cities. Each is a multiple of the same unit, and each is still counted in bits per second because that is what the optics and the copper actually carry.

Wireless has followed. The later wireless local network standards quote peak rates above a gigabit per second, though those figures assume a single device, ideal conditions and the full width of the channel. Real wireless throughput in a normal home is typically a third to a half of the advertised peak, and the gap widens with every additional device.

One gigabit per second equals 1,000,000,000 bits per second, 125 megaoctets per second, or about 0.9313 gibibits per second.