Conversion from Square miles to Square decimeters

Information about the Square mile (sq mi)

The square mile is a unit of area equal to 640 acres, or 2.589988 square kilometres. Its symbol is sq mi. It is the area of a square one mile on a side, and it is the unit in which American and British counties, cities, parks and disaster zones are described. Its equivalence to exactly 640 acres is not an accident but the foundation of how much of North America was laid out.

The United States Public Land Survey, begun in 1785, divided the western territories into townships of six miles square, each containing thirty-six sections of one square mile. A section holds 640 acres, a quarter section 160, and a quarter of that 40. Those numbers ran through homestead law, land sales and inheritance for a century, and they are still visible from the air in the grid of roads that follows section lines across the Midwest.

Because the survey made the square mile a legal container rather than a mere measurement, it shaped settlement patterns. A quarter section was considered the amount of land a family could work, so farms across the plains came in multiples of 160 acres, and the mile spacing of section-line roads set how far apart towns, schools and grain elevators could usefully sit.

Today its everyday use is descriptive. Population density in American statistics is people per square mile, so around 92 for the country as a whole against nearly 30,000 for Manhattan. Wildfire extent, flood inundation, national park size and metropolitan area are all reported the same way, and British usage matches it for county and national park areas even where other measurements have gone metric.

Converting is straightforward if the factor is remembered: one square mile is 2.59 square kilometres, and one square kilometre is 0.386 square miles. The relationship is not intuitive because it is the square of the length ratio, so a place described as ten times larger in square miles is only about 3.2 times larger in linear extent.

Its awkwardness shows when the three imperial land units are chained. A square mile is 640 acres, an acre is 4840 square yards, and a square yard is nine square feet, so going from a square mile to a square foot means multiplying by 27,878,400. That figure is exactly why land and building are measured with different units even inside the same system.

One square mile equals 640 acres, about 2.59 square kilometres, 259 hectares, or 27,878,400 square feet.

Information about the Square decimeter (dm²)

The square decimetre is a unit of area equal to one hundredth of a square metre, or one hundred square centimetres. It is written dm². It is the area of a square ten centimetres on a side, which is about the size of a palm or a drinks coaster, and it sits in the gap between the square centimetre of small objects and the square metre of rooms.

The decimetre owes its survival to volume rather than to area. A cubic decimetre is exactly one litre, which quietly builds the prefix into the most used volume unit in the world, and a square decimetre is the cross-section of that litre cube. Anyone who can picture a litre carton already knows what a square decimetre looks like: it is the face of the box.

Its one substantial commercial home is the leather trade. Hides are irregular, so they are measured by area rather than by length, and European tanneries, shoe factories and leather goods makers buy and sell in square decimetres. A whole cowhide runs to something like 200 to 250 square decimetres, a lambskin to about 50, and prices, cutting yields and waste allowances are all calculated on that basis. British and American buyers use square feet for the same purpose, and one square foot is 9.29 square decimetres.

Everyday objects land conveniently on it. A sheet of A4 paper is 6.24 square decimetres, a standard floor tile of thirty centimetres is nine, and a large postage stamp is a small fraction of one. Schools use the unit for exactly this reason: it lets a class measure real objects without either very large or very small numbers, and it makes the squaring rule visible, since ten centimetres on a side gives a hundred square centimetres.

Outside those uses it is rare, and for the usual reason. Engineering standardised on prefixes that step by a factor of a thousand, so square millimetres, square metres and square kilometres cover everything in practice. Ten square decimetres is more naturally written as 0.1 square metres, which sorts correctly beside every other figure in a specification.

Converting is straightforward once the squaring is kept in mind. Multiply by a hundred for square centimetres, divide by a hundred for square metres, and remember that the factor between neighbouring units is the square of the factor between the lengths, not the factor itself.

One square decimetre equals 100 square centimetres, 0.01 square metres, or about 15.5 square inches.