| Square inches (sq in) | Square millimeters (mm²) |
|---|---|
| 1 Square inch | 645.16 mm² |
| 2 Square inches | 1290.32 mm² |
| 3 Square inches | 1935.48 mm² |
| 4 Square inches | 2580.64 mm² |
| 5 Square inches | 3225.8 mm² |
| 10 Square inches | 6451.6 mm² |
| 20 Square inches | 12903.2 mm² |
| 25 Square inches | 16129 mm² |
| 50 Square inches | 32258 mm² |
| 100 Square inches | 64516 mm² |
| Reference | Square inches (sq in) | Square millimeters (mm²) |
|---|---|---|
| A sheet of A4 paper | 96.6737 sq in | 62370 mm² |
| A tennis court | 404241 sq in | 260800000 mm² |
| A football pitch | 11067022 sq in | 7.14 × 109 mm² |
| One hectare | 15500031 sq in | 1 × 1010 mm² |
| Central Park, New York | 5.28551 × 109 sq in | 3.41 × 1012 mm² |
The square inch is a unit of area equal to 6.4516 square centimetres exactly. Its symbol is sq in, sometimes written in². It is the area of a square one inch on a side, and one hundred and forty-four of them make a square foot. Its most important use is not as an area at all but as the denominator of the pound per square inch, the pressure unit that governs tyres, hydraulics and gas supply across the English-speaking world.
That pressure unit does most of the work. A car tyre is inflated to around 32 pounds per square inch, a bicycle tyre to 80 or more, a domestic water supply arrives at 40 to 60, and hydraulic machinery runs at several thousand. Because a hydraulic cylinder produces a force equal to pressure times piston area, the square inch is what turns a pressure gauge reading into a load, which is why the unit is printed on machinery even in workshops that measure everything else in millimetres.
Materials strength uses a multiple of it. Steel and aluminium are rated in thousands of pounds per square inch, written ksi, and a common structural steel yields near 50 ksi. Concrete in the United States is specified in pounds per square inch, with 3000 to 5000 typical for building work. The corresponding metric figures in megapascals are smaller by a factor of about 6.9, and mixing the two produces some of the most dangerous errors in engineering.
As a plain area it describes small flat things. A postage stamp is about one square inch, a large coin rather less, a credit card about 3.3, and the die inside a large processor around one. Gaskets, contact patches, wound dressings, printed labels and machined faces are all quoted in square inches in American workshops.
The conversion to metric is exact rather than approximate. Because the inch is defined as exactly 2.54 centimetres, one square inch is exactly 6.4516 square centimetres, or 645.16 square millimetres. The exactness is worth knowing, because it means a converted figure can be checked rather than merely trusted.
Its awkwardness lies in the ladder above it. A square foot is 144 square inches and a square yard is 1296, so imperial area arithmetic never reduces to shifting a decimal point. That is the practical reason engineering drawing in Britain moved to millimetres while American practice stayed with the inch and simply accepted the multiplication.
One square inch equals 6.4516 square centimetres, 645.16 square millimetres, or about 0.006944 square feet.
The square millimetre is a unit of area equal to one millionth of a square metre, written mm². It is the area of a square one millimetre on a side. It is the standard unit of engineering cross-sections, and two of the most consequential numbers in construction and electrical work are expressed in it.
Electrical cable is the first of those. Outside North America, conductors are specified by their cross-sectional area in square millimetres: 1.5 mm² for lighting circuits, 2.5 mm² for socket outlets, 6 mm² for a cooker, and 16 or 25 mm² for a house supply. Current-carrying capacity follows the area closely, so a 2.5 mm² copper conductor safely carries about twenty amperes in ordinary domestic installation, and the whole of wiring regulation is built on that relationship.
North America uses American Wire Gauge instead, where the numbers run backwards and the steps are not proportional: gauge 14 is about 2.08 mm² and gauge 12 about 3.31. Converting between the two systems is one of the more error-prone tasks in electrical work, because a gauge number carries no information about area until it is looked up.
The second consequential use is stress. One newton per square millimetre is exactly one megapascal, which is why structural drawings state steel and concrete strengths in N/mm². A common structural steel is designated S355 because it yields at 355 newtons per square millimetre, and a concrete grade of C30/37 reaches 30 newtons per square millimetre in cylinder testing. Bolts are rated the same way, using their tensile stress area: an M10 bolt has 58 square millimetres of it.
Electronics measures its products here too. A large processor die covers between 300 and 600 square millimetres, and the cost of a chip is driven directly by that number because a wafer holds a fixed area. A full-frame camera sensor is 864 square millimetres against roughly 30 for a phone camera, which is most of the reason the two behave so differently in low light.
Below the square millimetre the metric ladder continues to the square micrometre, used for transistors and cell biology, but almost nothing in ordinary manufacturing needs to go further. Above it, the square centimetre takes over at a hundred square millimetres.
One square millimetre equals 0.01 square centimetres, 0.000001 square metres, or about 0.00155 square inches.