Conversion from Cubic millimeters per second to Cubic centimeters per second

Information about the Cubic millimeter per second (mm³/s)

The cubic millimetre per second is a unit of volumetric flow rate equal to one cubic millimetre passing a point every second. Its symbol is mm³/s. A cubic millimetre is the volume of a grain of coarse salt, so this unit describes flows small enough that a full second delivers something barely visible.

Additive manufacturing made it a working number. A fused-filament printer's extruder is limited by how fast it can melt plastic, and that limit is expressed as a volumetric rate: a standard hot end manages 8 to 12 cubic millimetres per second, a high-flow one 25 to 40. Slicing software converts it into a print speed by dividing by the cross-section of the extruded line, which is why the same printer runs faster with a thin layer than a thick one.

Inkjet printing works at a far smaller scale still. A single droplet is a few picolitres, and a print head firing thousands of droplets per second from hundreds of nozzles adds up to only a few cubic millimetres per second in total. The unit is convenient here because it sits between the droplet and the ink cartridge without needing scientific notation.

Machining uses it for the material-removal rate of fine work. Wire electrical-discharge machining removes 20 to 100 cubic millimetres per minute, which is under two per second, and micro-milling with a tool a fraction of a millimetre across is slower again. Since removal rate governs both time and tool wear, it is the number a process engineer optimises.

Medical and laboratory devices are specified here when the volumes are tiny. Microfluidic chips, capillary electrophoresis and some infusion applications move flows of this order, and a cubic millimetre per second is exactly one microlitre per second, which is why the same rate appears under two names in different catalogues.

The unit's relation to the litre is worth holding: a million cubic millimetres make a litre, so a thousand cubic millimetres per second is one litre per second. A flow of ten cubic millimetres per second, typical of a 3D printer, would take about twenty-eight hours to fill a one-litre bottle.

One cubic millimetre per second equals 0.001 millilitres per second, 0.06 millilitres per minute, or one microlitre per second.

Information about the Cubic centimeter per second (cm³/s)

The cubic centimetre per second is a unit of volumetric flow rate equal to one cubic centimetre passing a point every second. Its symbol is cm³/s, and because a cubic centimetre is exactly a millilitre, the same rate is often written mL/s. It sits in the gap between the laboratory and the workshop: small enough to measure with a syringe, large enough to see.

Physiology uses it constantly. Resting cardiac output of five litres a minute is about 83 cubic centimetres per second, urine production is roughly 0.017, and a quiet breath moves perhaps 500 cubic centimetres over two seconds. Because the human body deals in volumes of this order, medical devices from ventilators to infusion pumps are calibrated in it.

Gas flow measurement adopted it early. A rotameter — the tapered glass tube with a float that appears on every laboratory bench — is graduated in cubic centimetres per second or per minute, and the float position gives the flow directly. Since a gas expands, such readings are meaningful only when the temperature and pressure are stated, which is why standard conditions accompany them.

Engines make an instructive example. A four-stroke engine of 2,000 cubic centimetres running at 3,000 revolutions per minute draws air through its intake at 1,500 cubic centimetres per revolution, or 75,000 cubic centimetres per second at 100 per cent volumetric efficiency. The mass air-flow sensor in the intake measures a quantity closely related to this, and the fuelling calculation depends on it.

Laboratory chromatography and analysis are specified here as well. A gas chromatograph column carries carrier gas at one to two cubic centimetres per minute, while a detector's make-up flow may be twenty or thirty, and the ratio between them determines the shape of the peaks the instrument reports.

The unit's convenience comes from the size of the cubic centimetre itself. A thousand of them make a litre, so a thousand cubic centimetres per second is a litre per second — a bath filling in about two minutes. Anything a person can pour by hand lies within a factor of a hundred of this rate.

One cubic centimetre per second equals one millilitre per second, 0.001 litres per second, or 60 cubic centimetres per minute.