Conversion from 5 Millimeters to Hands

Information about the Millimeter (mm)

The millimetre is one thousandth of a metre, written mm. It is the smallest division marked on most rulers and tape measures, which makes it the practical floor of everyday measurement in countries using the metric system.

Technical drawing has settled on the millimetre almost universally. Mechanical engineering drawings state dimensions in millimetres by default, usually without writing the unit at all, because the convention is understood. This avoids the decimal points that centimetres would introduce and the large numbers that micrometres would require. A component 45.5 mm long is easier to read and harder to misinterpret than one 4.55 cm or 45500 µm long.

Meteorology uses the millimetre for rainfall. A reading of 25 mm means that rain would stand 25 millimetres deep on a flat surface that did not drain, which corresponds to 25 litres per square metre. Snowfall is usually reported as depth in centimetres and separately as liquid water equivalent in millimetres.

Medicine relies on the unit for tumour dimensions, wound measurement and the size of anatomical structures on imaging. Ophthalmic prescriptions specify pupillary distance in millimetres. Blood pressure retains the older unit of millimetres of mercury, a pressure measurement whose name preserves the height of a mercury column.

Paper, sheet metal and glass are specified by thickness in millimetres. A standard sheet of office paper is about 0.1 mm thick. Domestic window glass is commonly 4 mm. Firearm and ammunition calibres are frequently given in millimetres, as in 9 mm.

Fastener sizes follow the unit closely. Metric bolts and screws are designated by their nominal diameter in millimetres, so an M8 bolt has an eight-millimetre thread. Spanner and socket sizes are marked the same way, measuring across the flats of the fastener head. This is why a metric toolkit contains an unbroken run of sizes rather than the fractional inch steps of an imperial set.

Medicine measures pressure with it as well as distance. Blood pressure is reported in millimetres of mercury, the height of a mercury column the pressure would support, so a healthy reading of 120 over 80 refers to two lengths rather than to any force directly. The convention dates from the mercury manometer and has survived every instrument that replaced it, because the numbers are familiar to every clinician alive. The same unit measures intraocular pressure in the eye, central venous pressure and the partial pressures of gases in blood, and it appears in vacuum work as the torr, which is one millimetre of mercury under another name.

One millimetre equals 1000 micrometres, 0.1 centimetres, or 0.001 metres. It is roughly 0.03937 inches, so 25.4 millimetres make exactly one inch.

Information about the Hand (hh)

The hand is a unit of length equal to exactly four inches, or 101.6 millimetres. It survives in one specialised application: measuring the height of horses and ponies. Almost nowhere else is it still in use.

The measurement is taken from the ground to the withers, the ridge between the shoulder blades where the neck meets the back. The withers are chosen because they are a fixed skeletal point that does not move as the horse raises or lowers its head, so the figure is reproducible in a way that measuring to the top of the head would not be.

Notation is unusual and frequently misread. Heights are written with a decimal point that does not indicate a decimal fraction. A horse of 15.2 hands stands fifteen hands and two inches, which is 62 inches or 157.5 centimetres. Because a hand is four inches, the digit after the point runs only from 0 to 3, and 15.4 is not a valid height. The abbreviation hh, for hands high, is common.

The boundary between a pony and a horse is conventionally set at 14.2 hands, though the exact threshold varies between breed registries and competitive disciplines. Draught breeds such as the Shire commonly exceed 17 hands. The tallest horses on record have stood over 20 hands.

The unit derives from the breadth of a human palm, an origin shared with several ancient measures. Egyptian and Roman systems both used a palm of comparable size. Its standardisation at four inches in England is usually credited to a statute of Henry VIII. The persistence of the hand in equestrian use is largely conservatism, and metric heights in centimetres are now given alongside it in international competition rules.

Measuring accurately is harder than it appears. The horse must stand square on level ground with its head in a natural position, and a purpose-made measuring stick with a spirit level and sliding crossbar is used rather than a tape. Shoeing adds height, so official measurements specify whether the horse is shod, and competition rules that impose height limits require certification by an appointed measurer.

One hand equals 4 inches, 101.6 millimetres, or 0.1016 metres.