Conversion from 5 Kilopascals to Pascals

Information about the Kilopascal (kPa)

The kilopascal is a unit of pressure equal to one thousand pascals. Its symbol is kPa. It is a hundredth of a bar and ten hectopascals, and it is the coherent SI unit that engineering was meant to adopt when the pascal proved too small to write comfortably. Standard atmospheric pressure is 101.325 kilopascals.

Tyres are where most people meet it. Canada, Australia, New Zealand and much of Asia state recommended tyre pressures in kilopascals, so a car door placard reads 220 or 240 rather than 32 or 35 pounds per square inch. The two scales sit side by side on most modern gauges, and the conversion is close to seven kilopascals to the pound per square inch.

Civil engineering uses it for loads on ground and structure. The bearing capacity of a soil is quoted in kilopascals, a firm clay allowing perhaps 150 and a soft one much less, and wind loading on a facade is calculated in the same unit. Because a kilopascal is also a kilonewton per square metre, structural calculations move between force and pressure without a conversion factor.

Medicine uses it in one important place. Arterial blood gases are reported in kilopascals in Britain, Ireland and much of Europe, where a healthy oxygen partial pressure is eleven to thirteen, while the United States reports the same measurement in millimetres of mercury as eighty to a hundred. The two numbers describe identical blood, and a clinician reading a foreign chart must know which convention it follows.

Vacuum work counts downward in it. A rough vacuum is a few kilopascals absolute, a domestic vacuum cleaner pulls perhaps twenty kilopascals below atmospheric, and freeze-drying operates well under one. Stating vacuum as an absolute pressure in kilopascals avoids the ambiguity of describing it as a negative gauge pressure.

Its awkwardness is only rhetorical. A hundred kilopascals is exactly one bar and reads less neatly, which is why the bar has held on in Europe despite decades of official preference for the pascal. Where the kilopascal has won, as on Canadian and Australian tyre placards, it has done so because the number is printed rather than spoken.

One kilopascal equals 1000 pascals, 0.01 bar, 10 hectopascals, or about 0.145 pounds per square inch.

Information about the Pascal (Pa)

The pascal is the SI unit of pressure, written Pa. It is defined as one newton of force spread over one square metre, and it is named after Blaise Pascal, whose experiments with barometers in the 1640s established that air has weight and that its pressure falls with altitude. The General Conference on Weights and Measures adopted the name in 1971.

It is a remarkably small unit. Atmospheric pressure at sea level is 101,325 pascals, so the pressure everyone lives under is a six-figure number, and almost every practical use of the unit therefore carries a prefix. That awkwardness is not a design fault but a consequence of coherence: the newton and the square metre were fixed first, and the pascal is whatever falls out of dividing one by the other.

Acoustics is the field where bare pascals are natural. The reference pressure for the decibel scale is twenty micropascals, taken as the quietest sound a healthy young ear can detect, and ordinary conversation is around 0.02 pascals of sound pressure. The threshold of pain sits near 63 pascals, so the entire range of human hearing spans about six orders of magnitude in this unit.

Everyday objects give a sense of the scale. A sheet of office paper lying flat presses on the desk with about 0.8 pascals. A gentle breeze exerts a few pascals on a wall, and the pressure difference that drives ventilation through a building is typically between ten and fifty. Anything a person can feel as force is already in the thousands.

Prefixed forms carry the real work. Weather uses hectopascals, which are numerically identical to the older millibars, so a forecast reading of 1013 needed no relearning. Engineering uses kilopascals for tyre and fluid pressures, and materials science uses megapascals and gigapascals for strength and stiffness, where one megapascal is one newton per square millimetre.

The pascal also appears wherever a stress rather than a pressure is meant, since the two have the same dimensions. Young's modulus, yield strength and shear stress are all quoted in pascals or their multiples, which is why a single unit spans the pressure in a tyre and the stiffness of steel.

One pascal equals 1 newton per square metre, 0.01 millibars, about 0.0000099 atmospheres, or about 0.000145 pounds per square inch.