Conversion from 5 Decares to Square inches

Information about the Decare (daa)

The decare is a unit of area equal to ten ares, or one thousand square metres. Its symbol is daa. Ten decares make one hectare. Unlike the other members of the are family it is in daily commercial use, though under several different names, because it happened to match land measures that a number of countries were already using when they went metric.

Norway is the clearest case. The Norwegian mål was redefined as exactly one thousand square metres in the metrication of the late nineteenth century, and dekar has been the working unit of Norwegian farming and forestry ever since. Agricultural statistics, subsidy applications and farm sale advertisements are all written in dekar, and a typical Norwegian holding runs to a few hundred of them.

The eastern Mediterranean tells a similar story with different words. The Greek stremma became one thousand square metres on metrication in 1899, the Turkish dönüm was fixed at the same figure, and the metric dunam of Israel, Jordan and Iraq matches both. Bulgaria uses the decare directly, and its farm census is published in it. In each of these places a traditional unit of roughly this size was rounded to the metric value rather than abolished.

The reason it works is that a thousand square metres suits smallholdings. A hectare is a large field, and a hundred square metres is a garden; the decare falls between them, at about the size of an orchard plot, a vineyard parcel or a village building lot. It is also close to a quarter of an acre, which is why it reads naturally to people brought up with either system.

Reporting to international bodies converts it away. European Union agricultural returns, the statistics of the Food and Agriculture Organization and most academic work are all in hectares, so national figures in dekar or stremmata are divided by ten before they travel. This is a frequent source of order-of-magnitude errors in translated agricultural reporting, since a farm of 300 dekar is 30 hectares and not 300.

The symbol daa is awkward but unambiguous, being the deca prefix applied to the are. It should not be confused with da, which is the deciare and one hundred times smaller, nor with the prefix symbol da used before other units.

One decare equals 1000 square metres, 10 ares, 0.1 hectares, or about 0.247 acres.

Information about the Square inch (sq in)

The square inch is a unit of area equal to 6.4516 square centimetres exactly. Its symbol is sq in, sometimes written in². It is the area of a square one inch on a side, and one hundred and forty-four of them make a square foot. Its most important use is not as an area at all but as the denominator of the pound per square inch, the pressure unit that governs tyres, hydraulics and gas supply across the English-speaking world.

That pressure unit does most of the work. A car tyre is inflated to around 32 pounds per square inch, a bicycle tyre to 80 or more, a domestic water supply arrives at 40 to 60, and hydraulic machinery runs at several thousand. Because a hydraulic cylinder produces a force equal to pressure times piston area, the square inch is what turns a pressure gauge reading into a load, which is why the unit is printed on machinery even in workshops that measure everything else in millimetres.

Materials strength uses a multiple of it. Steel and aluminium are rated in thousands of pounds per square inch, written ksi, and a common structural steel yields near 50 ksi. Concrete in the United States is specified in pounds per square inch, with 3000 to 5000 typical for building work. The corresponding metric figures in megapascals are smaller by a factor of about 6.9, and mixing the two produces some of the most dangerous errors in engineering.

As a plain area it describes small flat things. A postage stamp is about one square inch, a large coin rather less, a credit card about 3.3, and the die inside a large processor around one. Gaskets, contact patches, wound dressings, printed labels and machined faces are all quoted in square inches in American workshops.

The conversion to metric is exact rather than approximate. Because the inch is defined as exactly 2.54 centimetres, one square inch is exactly 6.4516 square centimetres, or 645.16 square millimetres. The exactness is worth knowing, because it means a converted figure can be checked rather than merely trusted.

Its awkwardness lies in the ladder above it. A square foot is 144 square inches and a square yard is 1296, so imperial area arithmetic never reduces to shifting a decimal point. That is the practical reason engineering drawing in Britain moved to millimetres while American practice stayed with the inch and simply accepted the multiplication.

One square inch equals 6.4516 square centimetres, 645.16 square millimetres, or about 0.006944 square feet.