Conversion from 3 Kilopascals to Centipascals

Information about the Kilopascal (kPa)

The kilopascal is a unit of pressure equal to one thousand pascals. Its symbol is kPa. It is a hundredth of a bar and ten hectopascals, and it is the coherent SI unit that engineering was meant to adopt when the pascal proved too small to write comfortably. Standard atmospheric pressure is 101.325 kilopascals.

Tyres are where most people meet it. Canada, Australia, New Zealand and much of Asia state recommended tyre pressures in kilopascals, so a car door placard reads 220 or 240 rather than 32 or 35 pounds per square inch. The two scales sit side by side on most modern gauges, and the conversion is close to seven kilopascals to the pound per square inch.

Civil engineering uses it for loads on ground and structure. The bearing capacity of a soil is quoted in kilopascals, a firm clay allowing perhaps 150 and a soft one much less, and wind loading on a facade is calculated in the same unit. Because a kilopascal is also a kilonewton per square metre, structural calculations move between force and pressure without a conversion factor.

Medicine uses it in one important place. Arterial blood gases are reported in kilopascals in Britain, Ireland and much of Europe, where a healthy oxygen partial pressure is eleven to thirteen, while the United States reports the same measurement in millimetres of mercury as eighty to a hundred. The two numbers describe identical blood, and a clinician reading a foreign chart must know which convention it follows.

Vacuum work counts downward in it. A rough vacuum is a few kilopascals absolute, a domestic vacuum cleaner pulls perhaps twenty kilopascals below atmospheric, and freeze-drying operates well under one. Stating vacuum as an absolute pressure in kilopascals avoids the ambiguity of describing it as a negative gauge pressure.

Its awkwardness is only rhetorical. A hundred kilopascals is exactly one bar and reads less neatly, which is why the bar has held on in Europe despite decades of official preference for the pascal. Where the kilopascal has won, as on Canadian and Australian tyre placards, it has done so because the number is printed rather than spoken.

One kilopascal equals 1000 pascals, 0.01 bar, 10 hectopascals, or about 0.145 pounds per square inch.

Information about the Centipascal (cPa)

The centipascal is a unit of pressure equal to one hundredth of a pascal. Its symbol is cPa. It is a legitimate metric combination that almost nobody writes, and understanding why it is unused says more about how pressure is actually recorded than a list of its applications ever could.

The centi prefix has one great success behind it, the centimetre, and that success came from the human scale of the metre. A metre is too long for the width of a hand and a millimetre too short, so the centimetre filled a real gap. Pressure has no comparable gap. The pascal is already so small that dividing it further gives numbers no instrument in ordinary use can resolve.

A centipascal is one hundredth of the pressure of a sheet of paper on a table. It is the pressure difference across a millimetre of air, or roughly what a grain of sand exerts spread over a fingernail. Nothing in engineering, meteorology or building practice needs that resolution: airtightness testing works at fifty pascals, ventilation at a few hundred, and weather at tens of thousands.

Where pressures smaller than a pascal do matter — acoustics and vacuum work — the convention jumps straight to the millipascal and the micropascal, because those fit the thousand-step ladder that the rest of the measurement system uses. A sound pressure of 20 millipascals is written that way rather than as 2 centipascals, even though the two are the same, because everything around it on the page is in thousand-step units.

The unit is nevertheless well defined, and that is the metric system working as designed. Every prefix combines with every unit without exception, so a reader who has never seen cPa can still decode it on sight from the prefix alone. A system with gaps would require a table; a system without them requires only the rule.

Occasional appearances do occur. Older instrument manuals sometimes use it, some national standards mention it in passing, and a few specialist fields adopt it locally when their numbers happen to fall between one and a hundred in that unit. A converter has to handle it for exactly those cases.

One centipascal equals 0.01 pascals, 10 millipascals, 0.1 decipascals, or about 0.00000145 pounds per square inch.