Conversion from 2 Square millimeters to Square decimeters

Information about the Square millimeter (mm²)

The square millimetre is a unit of area equal to one millionth of a square metre, written mm². It is the area of a square one millimetre on a side. It is the standard unit of engineering cross-sections, and two of the most consequential numbers in construction and electrical work are expressed in it.

Electrical cable is the first of those. Outside North America, conductors are specified by their cross-sectional area in square millimetres: 1.5 mm² for lighting circuits, 2.5 mm² for socket outlets, 6 mm² for a cooker, and 16 or 25 mm² for a house supply. Current-carrying capacity follows the area closely, so a 2.5 mm² copper conductor safely carries about twenty amperes in ordinary domestic installation, and the whole of wiring regulation is built on that relationship.

North America uses American Wire Gauge instead, where the numbers run backwards and the steps are not proportional: gauge 14 is about 2.08 mm² and gauge 12 about 3.31. Converting between the two systems is one of the more error-prone tasks in electrical work, because a gauge number carries no information about area until it is looked up.

The second consequential use is stress. One newton per square millimetre is exactly one megapascal, which is why structural drawings state steel and concrete strengths in N/mm². A common structural steel is designated S355 because it yields at 355 newtons per square millimetre, and a concrete grade of C30/37 reaches 30 newtons per square millimetre in cylinder testing. Bolts are rated the same way, using their tensile stress area: an M10 bolt has 58 square millimetres of it.

Electronics measures its products here too. A large processor die covers between 300 and 600 square millimetres, and the cost of a chip is driven directly by that number because a wafer holds a fixed area. A full-frame camera sensor is 864 square millimetres against roughly 30 for a phone camera, which is most of the reason the two behave so differently in low light.

Below the square millimetre the metric ladder continues to the square micrometre, used for transistors and cell biology, but almost nothing in ordinary manufacturing needs to go further. Above it, the square centimetre takes over at a hundred square millimetres.

One square millimetre equals 0.01 square centimetres, 0.000001 square metres, or about 0.00155 square inches.

Information about the Square decimeter (dm²)

The square decimetre is a unit of area equal to one hundredth of a square metre, or one hundred square centimetres. It is written dm². It is the area of a square ten centimetres on a side, which is about the size of a palm or a drinks coaster, and it sits in the gap between the square centimetre of small objects and the square metre of rooms.

The decimetre owes its survival to volume rather than to area. A cubic decimetre is exactly one litre, which quietly builds the prefix into the most used volume unit in the world, and a square decimetre is the cross-section of that litre cube. Anyone who can picture a litre carton already knows what a square decimetre looks like: it is the face of the box.

Its one substantial commercial home is the leather trade. Hides are irregular, so they are measured by area rather than by length, and European tanneries, shoe factories and leather goods makers buy and sell in square decimetres. A whole cowhide runs to something like 200 to 250 square decimetres, a lambskin to about 50, and prices, cutting yields and waste allowances are all calculated on that basis. British and American buyers use square feet for the same purpose, and one square foot is 9.29 square decimetres.

Everyday objects land conveniently on it. A sheet of A4 paper is 6.24 square decimetres, a standard floor tile of thirty centimetres is nine, and a large postage stamp is a small fraction of one. Schools use the unit for exactly this reason: it lets a class measure real objects without either very large or very small numbers, and it makes the squaring rule visible, since ten centimetres on a side gives a hundred square centimetres.

Outside those uses it is rare, and for the usual reason. Engineering standardised on prefixes that step by a factor of a thousand, so square millimetres, square metres and square kilometres cover everything in practice. Ten square decimetres is more naturally written as 0.1 square metres, which sorts correctly beside every other figure in a specification.

Converting is straightforward once the squaring is kept in mind. Multiply by a hundred for square centimetres, divide by a hundred for square metres, and remember that the factor between neighbouring units is the square of the factor between the lengths, not the factor itself.

One square decimetre equals 100 square centimetres, 0.01 square metres, or about 15.5 square inches.